Energy-efficient short-wave heat lamps from Under Control Instruments are designed
for use in heated counters and serveries by catering equipment manufacturers. The
lamps are available in overall a lengths of 220mm, and supplied in 300 and 500W
The lamps promise a working life of 8000 hours across the whole range, which is 60%
longer than most competing units, which only offer 5000 hours of operation.
Novel design features give them stability in catering environments at competitive
All lamps are CE approval and manufactured to EN60335-1:2005 and EN60335-2-30:2003,
the Low Voltage Directive 2006/95/EC and the RoHS Directive.
These lamp holders are made from polished reflective stainless steel and not from
aluminium like others. Almost all of the heat is projected forward. This gives optimum
use of the lamps energy and prevents the holder from absorbing the heat and overheating.
This in turn causes failures of the connector ends and cabling. We offer these holders
to suit all catering lamps 220mm long with R7S push in ends. They are fitted with
a 6A rated ceramic spring terminals and will suit jacketed or un-jacketed lamps.
These lamp holders are to suit lamps that are 118mm long lamps with R7S ends. They
have ceramic ends rated 6A with PTFE or fibreglass leads.
Reflector dish to suit all lamps and holders 118mm long with R7S push in ends.
Energy regulator (dimmers) with on/off switch suitable for controlling our range
of infra-red catering lamps, infrared heaters and elements available for 240 and
Low-cost digital controllers to be used as replacements for normal capillary thermostats.
New from Under Control Instruments, high-specification 8820 series digital controllers
are supplied as standard with a 20A main relay outputs and two NTC sensors for controlling
temperatures from -50 to 150 deg C. They are suitable for many applications requiring
on/off heating and cooling control.
Hot air circulation fan are for use in a wide range of kitchen equipment.
Under Control Instruments now offers a range of circulation fans specifically for
catering equipment manufacturers. They are designed to improve the heat circulation
within ovens and hot cupboards and are ideal for application in equipment such as
ovens, climate cabinets, meal and dish warmers etc.
The design combines a radial impeller (cooling fan) made of sheet steel and a mounting
plate (heat shield) to set the motor away from the hot area.
High-temperature-resistant lubricant is used for the sleeve bearings, and the winding
insulation is class H.
Catering Heat Lamps 220mm long
AC Energy Regulator (Dimmer)
118mm Lamp Reflector
118mm Lamp Holder
Lamp Holder 220mm long
Hot Cupboard Fan
8820 Temperature Controller
The U.C.I Serving hot tops are fitted into catering servery hot counters to give
the user a controllable food surface serving temperature. The glass can either manufactured
from ceramic toughened glass. This gives strength, stability, safety, the surface
is also easily cleanable. The ceramic glass has a maximum working temperature of
750°C, and the toughened glass of 200 deg C, both are fitted with a heated element
suitable for controlling up to 120 deg C
Servery Hot Top counters
Under Control Instruments has a new range of ceramic long-wave infra-red heaters
The heaters are CE and UL approved and will give performance of between 5000 and
They are available in standard sizes of 245 x 60, 122 x 60 and 122 x 122mm, and are
also available with a flat-face design.
These heaters are used to keep food ware in display units.
Under Control instruments can also supply a range of accessories, including high-temperature
cables, ceramic blocks and energy regulators to suit.
Theses lamps lamps are of the same design and performance as the 220mm long lamp
above but 118mm long to suit different holders. They are available in wattages of
200,300 and 500w
Catering Heat Lamps 118mm long
A range of E.G.O thermostats suitable for temperature ranges between -35 to +500ºC
See attached PDF for the the range we can offer.
EGO 50.57071.010 energy regulator. Double pole, rated 13.5A 240 Vac max. 6mm metal
spindle. For use with
Simmerstat knobs to suit EGO simmerstats with 6mm and 4.7 shafts, 0 - 6 and 1 - 4
These high quality ceramic terminal blocks make wiring connections to heaters efficient
and easy and have a touch safe design. Ovens, furnaces, kilns, infrared heaters,
quartz tube heaters, catering equipment, etc. Fitted with Nickel plated brass connectors,
they can withstand 250°C.
Available in ampages from 5 to 30A and 1 to 6 pole.
Ceramic Terminal Blocks
Rocker switch, DPST, illuminated, 15A, 250v, IO indicator marks. 22.3x30 cutout.
Supplied with PVC cover. Two designs are available that offer waterproofing and are
available suitable for round cutouts as well.
Indicator panel light, spade connectors, 220v to suit a 12mm cutout.